Furuno GP-150 User Manual Page 56
- Page / 97
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8. MENU SETTINGS
8-8
Setting DATA 4 to NMEA
The DATA 4 port connects to a personal
computer, DGPS receiver or YEOMAN
equipment.
1) Press MENU ESC, 9 and 5. The DATA 4
I/O SETUP (1/2) menu appears.
RS422
Data Out Com. DGPS
To Next Page
DATA 4 I/O SETUP 1/2
MENU : Escape
ENT : Enter
: Select
Appears only when external
DGPS receiver is used.
DATA 4. Level
RS232C
Figure 8-10 DATA 4 I/O SETUP menu (1/2)
2) Press
or to select Level.
3) Press
or to select level of external
equipment; RS232C or RS422.
4) Press the NU/CU ENT key.
5) Press
or to select Out.
6) Press
to select To Next Page. The
DATA 4 I/O SETUP (2/2) menu appears.
To Previous Page
Talker ID GP LC DE
Output Data (00-90 sec) 98%
DATA 4 I/O SETUP <Out> 2/2
MENU : Escape
ENT : Enter
Data Fmt. V1.5 V2.0 IEC
1. AAM:00 APA:00 APB:04 BOD:00
2. BWR:00 BWW:00 GGA:00 GLL:01
3. RMB:01 RMC:00 VTG:01 WCV:00
4. VDR:00 WPL:00 XTE:00 ZDA:01
5. GNS:00 GBS:01 Rnn:00 RTE:00
Figure 8-11 DATA 4 I/O SETUP menu (2/2)
7) Follow "DATA 1 output setting" from step
2.
8.5 Receiving Data from
Personal Computer
Loading Waypoints/Routes data
Waypoints and Routes data can be
downloaded from a personal computer,
through the DATA 4 connector.
1) Press MENU ESC, 9 and 5.
2) Press
or to select Level.
3) Press
or to select level of personal
computer; RS232C or RS422.
4) Press the NU/CU ENT key.
5) Press
to select Com.
6) Press
to select To Next Page. The
DATA 4 I/O SETUP menu appears.
To Previous Page
Baud Rate 9600 bps
Command Stop Start
Save Data WPT/RTE
Command Stop Start
DATA 4 I/O SETUP <Com.> 2/2
MENU : Escape
ENT : Enter
: Select
Load Data WPT/RTE WPT
Figure 8-12 DATA 4 I/O SETUP menu (2/2)
7) Press
or to select Baud Rate.
8) Press
or to select baud rate;
4800bps, 9600bps, or 19200bps.
9) Press the NU/CU ENT key.
10) Press
to select WPT/RTE.
11) Press
to select Command. Stop, on
the same line as Command, appears in
reverse video.
12) Press
to select Start. The message
shown in Figure 8-13 appears.
Loading erases current data
and stops Route navigation
Are you sure to load ?
ENT: Yes MENU:No
Figure 8-13
- GPS NAVIGATOR 1
- (( HIMAHIMA )) 2
- GP-150GP-150 2
- IMPORTANT NOTICE 3
- SAFETY INSTRUCTIONS 4
- TABLE OF 5
- CONTENTS 5
- FOREWORD 6
- SYSTEM CONFIGURATION 7
- 1. OPERATIONAL OVERVIEW 9
- 1.2 Turning On and Off the 10
- 1. OPERATION 11
- 1.3 Adjusting Display 11
- Contrast and Brilliance 11
- Plotter 1 display 12
- Plotter 2 display 12
- Navigation display 13
- : North mark 14
- : Demonstration display 14
- : Alarm is violated 14
- 2.1 Enlarging/Shrinking the 15
- Display 15
- 2.2 Selecting Display 15
- Orientation 15
- 2.3 Shifting the Cursor 15
- 2. TRACK 16
- Cursor turned off 16
- 2.10 Apportioning the 19
- 2.11 Selecting Bearing 20
- Reference 20
- Entering magnetic variation 20
- 3. MARKS 21
- 3.2 Selecting Mark Shape 22
- 3.3 Connecting Marks 22
- (selecting mark connection 22
- 3.4 Entering Event Marks 23
- 3.6 Entering the MOB Mark 24
- 4. NAVIGATION 25
- PLANNING 25
- 4. NAVIGATION PLANNING 26
- Registering waypoints by MOB 27
- ]) 3, 4, 1, 2, 3, 4. 5 28
- ]) 1, 3, 5, 2, 3, 4, 5, 6 28
- 4.2 Editing Waypoints 29
- 4.4 Registering Routes 30
- 4.5 Deleting Route 31
- Waypoints 31
- 4.7 Deleting Routes 32
- 5. STARTING FOR 33
- DESTINATION 33
- Repeat steps 34
- on the 35
- • By selecting route 36
- 5.2 Canceling Destination 37
- 5.3 Erasing Route 38
- Waypoints (flags) 38
- When flags are erased 38
- 5.4 Finding Range and 39
- Bearing Between Two 39
- 5. STARTING FOR DESTINATION 40
- 6. SETTING UP 41
- VARIOUS 41
- DISPLAYS 41
- Displaying LOPs 42
- to display LOPs 43
- 6.3 Demo Display 44
- 7. ALARMS 45
- 7.2 Cross Track Error (XTE) 46
- 7.3 Ship’s Speed Alarm 47
- 7.4 Trip Alarm 47
- 7.5 Water Temperature 48
- 7.6 Depth Alarm 48
- 7.7 WAAS/DGPS Alarm 48
- 8. MENU 49
- SETTINGS 49
- Selecting fix mode 50
- to switch from 51
- 5) If necessary press 51
- 8. MENU SETTINGS 52
- Entering position 52
- 8.3 Mark, Character Size 53
- 23.456' 54
- DATA 2 output setting 55
- DATA 3 output setting 55
- Setting DATA 4 to NMEA 56
- 9. MAINTE 61
- NANCE & 61
- TROUBLE 61
- SHOOTING 61
- 9.2 Preventive Maintenance 62
- DGPS error 63
- 9.4 Troubleshooting 64
- 9.5 Diagnostic Tests 65
- Memory and I/O circuits test 65
- Display test 66
- MENU TREE 67
- APPENDIX 68
- Time Diff. (+00:00) 69
- DIGITAL INTERFACE 70
- 4. Lon offset, min, E/W 78
- TIME DIFFERENCES 87
- GEODETIC CHART LIST 88
- LORAN C CHAINS 89
- DECCA CHAINS 90
- PARTS LIST 91
- Parts Location 92
- GP-150/Dual 93
- SP-2 E4440S01A-M 94
- Position-fixing Accuracy 1-2 96
- Declaration of conformity 97
Related products and manuals for Navigational compasses Furuno GP-150
Navigational compasses Furuno SC-60 User Manual
(106 pages)
(106 pages)
© 2020, manymanuals.com. All rights reserved. | 0.746 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals