Furuno FSV-24 User Manual

Installation Manual COLOR SCANNING SONAR FSV-24/24S SAFETY INSTRUCTIONS...i

1-2 600 10001300 650Heater Insulator Maintenance space, example sonar compartment Note: After mounting the equipment, install stays f

相互結線図INTERCONNECTION DIAGRAMDCBA654321FURUNO ELECTRIC CO., LTD.kgDRAWNCHECKEDAPPROVEDSCALEMASSDWG No.TITLENAME名称カラースキャニングソナー表示部 FSV-2400FSV-2401操作部CON

DCBA654321FURUNO ELECTRIC CO., LTD.kgDRAWNCHECKEDAPPROVEDSCALEMASSDWG No.TITLENAME名称INTERCONNECTION DIAGRAMCOLOR SCANNING SONAR相互結線図注記＊２）コネクタは工場にて取付済み

CB123DADWG.No.SCALECHECKEDAPPROVEDDRAWNMASSkg名称NAMETITLEINTERCONNECTION DIAGRAM制御部外部信号接続相互結線図PROCESSOR UNIT EXTERNAL INTERFACEJ10GNDSONDE_WLGNDGNDSOND

243A1BCDRAWNCHECKEDAPPROVEDDWG.No.TITLENAME名称相互結線図INTERCONNECTION DIAGRAMCS-120AインターフェイスINTERFACESCALE MASSkg0VSHIELD+24VDCJ201TD-HTD-CRD-HRD-CGNDDSR-

1-31.1.2 Shortening the retraction tank The retraction tank is 1300 mm in length when supplied. Shorten the tank as necessary so that the transducer

1-4 1.1.3 Remarks for installation of retraction tank 1. Make, if possible, the installation location a double bottom structure. 2. Install, if po

1-51.1.4 Installing hull unit on retraction tank After welding the retraction tank and allowing sufficient time for cooling, install the hull unit a

1-6Hex. NutSpring WasherFlat WasherBow MarkHull Unit FlangeO-ringTank FlangeFlat WasherHex. BoltHex. NutSpring WasherFlat WasherRetraction TankHex. B

1-71.1.5 Installing stays (anti-vibration measure) Install stays from the top of the hull unit to the ship’s hull. The stays should be angle iron wi

1-81.2 Mounting the Display Unit The display unit is composed of the processor, monitor and control units. 1.2.1 Processor unit Mounting consider

1-9Mounting procedure 1. Unfasten two bolts from the bottom of the front side of the processor unit, and pull the unit toward you to separate the un

1-10 Mounting procedure 1. Drill four holes of 12 mm in diameter in the mounting location, referring to the outline drawing for mounting dimensions.

1-11Attaching the CRT filter 1. Attach two spacer (5x2.5, supplied) with screws (M5x10, supplied) to the location shown below. 2. Screw two hood re

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANTelephone :

1-12 (2) Fixing without KB fixing plate 1) Drill four mounting holes of 6 mm diameter to fasten the control unit, referring to the outline drawing

1-13Passing the cable through the bottom of the control unit For permanent mounting ((2) and (3) above), the control cable can be passed through the

1-14 1.3 Mounting the Transceiver Unit The transceiver unit should be mounted on a mounting base (shipyard supply) whose dimensions are as shown in

1-151.5 Grounding the Equipment The power supply unit, processor unit and hull unit have protective grounding. Ground the units with a ground wire (

1-16Procedure 1. Clean the hull unit flange, O-ring and O-ring groove. Coat them with a slight amount grease. 2. (1200 mm stroke) Use 24 hex. bolts

1-17Hex. BoltFlat WasherO-ringSpring WasherFlat WasherHex. NutAttachment FlangeO-ringHex. NutSpring WasherFlat WasherHull Unit FlangeExisting Tank*:

1-18 1.7 Mounting the Cable for Extension Kit (option) For extension of the transducer cable between the hull unit and the transceiver unit, use the

1-191.8 Attachment Kit (option) When using the retraction tank of FSV-243E/244E for FSV-247/248, the optional attachment kit OP10-24 is necessary.

1-20Hex. boltSpring washerSpring washerFlat washerO-ringFlat washerInsulation gasket (2)Insulation gasketHex. boltHex. nutRetraction tankStern side(S

2-1122. WIRING 2.1 How to Use the Crimping Tool, Pin Extractor A special crimping tool is necessary for connection of wires to the contact pins of t

iSAFETY INSTRUCTIONSWARNINGTurn off the power at the switchboardbefore beginning the installation.Fire or electrical shock can result if thepower i

2-2 2.2 Location of Connectors Monitor(Local supply)CONTROL UNIT FSV-2401CONTROL UNIT FSV-2401MONITOR UNIT FSV-2400PROCESSOR UNITFSV-2402/2402SPOWER

2-310S214015m10S214114.5m1161160.46m0.5m13.3m0.48m13.3mTransceiver unit sideHull unit side10S20788m0.38m7.2m0.28m0.07m0.07mRaise/lower control box of

2-4 2.3 Monitor Unit 2.3.1 Fabrication of monitor cable 10S2074 (10 m)/10S2075 (30 m) 63214ARMORSHIELD1. GRY (No.1)2. BLK/WHT3. GRY (No.2)4. BLK/RED

2-5HousingClampWasherNutCenter PinGasket7.5Shield3Guide Pin AGuide Pin BGuide Pin B(Small)Guide Pin A(Large)Position No. Assembling 38P connector P

2-6 Assembling D-SUB connector (CN-A302) 1. Remove vinyl sheath of cores by 3 mm. 2. Pass the cores through shrink tubes (local supply). 3. Solder

2-72.3.3 How to connect cables to the monitor unit Connect the monitor cable and control cable to the monitor (FURUNO-supplied monitor) unit as be

2-8 2.4 Processor Unit Cables (10S2074, 10S1258-1 and control cable) from the various units are connected to the CONE Board (10P6905) via the cable c

2-9Fabrication of connector 00-8016-038-313761HV (CN-A101) 3204540ShieldAnticorrosiveSheathArmorVinyl SheathCoreInsulating TapeAfter exposing cores,

2-10 Armor Vinyl sheathTapingSolder lead wire to armor andconnect it to #1 pin of connector.ConductorS = 1.5 mm∅ = 1.56 mm2VinylsheathArmorCable DPYC

2-112.4.5 Optional equipment With connection of navigator and electronic fishing equipment, the function of the FSV-24 is expanded to include true mo

ii CAUTIONMaximum speed while the transducer isprojected and being raised or loweredis as below, to prevent damage to thetransducer.

2-12 8 cmSoldering sideSoldering-sideConnector caseConnector case1 cm2 cm3 mmShield2 cm3mmShieldVinyl sheathVinyl sheathVinyl sheathArmorSolder unuse

2-13Synchronizing with echo sounder or other sonar To synchronize the transmission of the FSV-24 with an echo sounder or other type of sonar, make co

2-14 2.5 Transceiver Unit 2.5.1 Fabrication of connector 00-8016-038-313761HV (CN-B101) 4004540ShieldAnticorrosiveSheathArmorVinyl SheathCoreInsula

2-152.5.2 Fabrication of power cable type DPYCY-4 (TB-B101) Fabricate the cable DPYCY-4 as below for connection to the power unit. ConductorS = 4 m

2-16 2.5.4 Connection 1. Open the transceiver unit cover. 2. Plug the XH connectors at the end of signal cables (10S2140, 10S2141) into the proper

2-172.6 Power Supply Unit Connect the power cable DPYCY-4 or equivalent as below. 0V100V0V100V110/115V0V220V230VFor 100/110/115 VAC For 220/230 VA

2-18 3. Starting from the right side of the junction box, fix the cables by CSK clamp, pass them through cable clamps and connect XH connectors to

2-192.7.2 Raise/Lower Control Box Connect power cable (3φ) and the transceiver unit cable (10S2078) as shown below. TB-C101Connect the power cable T

2-20100 2520FV5.5-4M4(yellow) x 3SheathArmor(Clamp here by cable clamp.)Vinyl sheath Power cable fabrication

3-13. ADJUSTMENT AND CHECK 3.1 Hull Unit Check Note: Before conducting this check (at the dry dock) transmission must be stopped. Default setting o

iiiSYSTEM CONFIGURATION Standard type Note 1: Power Kit FSV-2403 (option, installed inprocessor unit) required to connect CS-120A.TRANSCEIVERUNITFS

3-2 3. Select INITIAL SETTING and press the [MENU] key. CAUTIONTHIS ITEM IS DEFINED AS NON-CHANGEABLE ITEM, ARE YOU SURE TO CHANGE IT TO CHANGEABL

3-3How to check the hull unit 1. Press the POWER (|) switch on the control unit (for the display unit) to turn on the equipment. Confirm that the la

3-4 8. Check that LEDs on the panel of the raise/lower control box light as follows: a) UP, MD and DN LEDs light when corresponding limit switch is

3-5SYSTEM MENU QUITINTERFACE SETTING..EXT DATA SETTING..OWN SHIP MARK..TEST&INITIALIZATION..TRX SETTING 1..TRX SETTING 2..OTHERS.. SYSTEM menu 4

3-6 3.3 Configuring Own Ship Mark Set own ship’s dimensions and the location of the transducer to accurately display the own ship mark on the displa

3-75. Select ! or " and then press the [MENU] key several times to set the ship’s length (15 to 150 m). 6. Select QUIT to finish the setting. 7

3-8 3.4 Other SYSTEM Menu Items This section shows you how to set up external equipment. Default settings are underlined. 3.4.1 INTERFACE SETTING

3-93.4.2 EXT DATA SETTING menu EXT DATA SETTINGLOG PULSE : 200p/NM MENU QUITQUITSPEED&COURSE: NMEAHEADING: AD10SDATE&TIME: CIFSPEED SEN

3-10 WATER DEPTH Select the input port for the depth data. (NONE, CIF, NMEA) WATER TEMP. Select the input port for the water temperature data. (NONE

3-11LANGUAGE Select the language. (JAPANESE, ENGLISH) HEADING ADJUST See “3.2 Heading Adjustment”. ES2 SELECT Select the equipment connected to the

ivBlack box type Note 1: Power Kit FSV-2403 (option, installed inprocessor unit) required to connect CS-120A.TRANSCEIVERUNITFSV-241EPOWERSUPPLYUNITFS

3-12 3.5 CONE Board Setting in the Processor Unit Adjust the potentiometers on the CONE Board in the processor unit, referring to the table shown be

3-133.6 DIP Switch Setting Processor unit, inside view 3.6.1 CIF2/NMEA2 connector interface selection The signal format of the CIF2/NMEA2 port at

3-14 3.6.2 Selecting the Net Sonde information The net depth information from the Net Sonde can be entered from the FNZ port or CIF port. Dependi

3-153.7 Testing TX/RX independently at hull unit To check the Tx/Rx function of the hull unit independently, follow the steps below. Note: This tes

This page is intentionally left blank.

4-14. CONNECTING THE EXTERNAL INTERFACE CS-120A When upgrading from the CSH-20 series sonar, the External Interface CS-120A can be used. Connect bet

4-22. Remove two upset screws, detach the plugs J503, J502, J501, J504, J506 and J507, thus pull out the power block. IFES SCANSCAN2DUALDCONPower B

4-37. Connect between the processor unit and CS-120A as follows. CS-120AJ201Processor UnitYEL BRNBRNBRNPOWER FOR CS-120A portCIF1 or NMEA2/CIF2 por

AP-1 Check List Ship Name Date / / Location SCANNING SONAR TYPE FSV-24 RESULT Monitor unit (FSV-2400)

AP-2 DATA SHEET 1 General check CK; DT: digital tester AT: analog tester OS:oscilloscope WC:watch Check item Content Check

v EQUIPMENT LISTS Standard supply Name Type Code No. Q’ty Remarks Monitor Unit FSV-2400 - 1 21” color monitor Control Unit FSV-2401 - 1 w/cab

AP-3 DATA SHEET 2 DISPALY UNIT (FSV-2400 ) Check item Contents Check point CK Standard Result Judge Check software version on the each board

AP-4 DATA SHEET 3 User menu H-scan setting P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 Range Gain Tilt Tｘ interval

AP-5 TRX setting1 TRX setting1 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 TX weight RX weight-H RX weight-V

CODE NO.006-921-230-00TYPECP10-04501略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-6 INSTALLATION MATERIALS工事材料表10CO-X-9401ｺﾈ

CODE NO.006-921-240-00TYPECP10-04502略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-5 INSTALLATION MATERIALS工事材料表10CO-X-9402ｺﾈ

CODE NO.006-921-250-00TYPECP10-04503略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-4 INSTALLATION MATERIALS工事材料表10CO-X-9403ｺﾈ

CODE NO.TYPE略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-1 INSTALLATION MATERIALS工事材料表10CO-X-9412FSV-247/248圧着端子CRIMP-ON LU

CODE NO.006-921-290-00TYPECP10-04506略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-3 INSTALLATION MATERIALS工事材料表10CO-X-9406ｺﾈ

CODE NO.006-934-240-00TYPECP10-04801略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-1 INSTALLATION MATERIALS工事材料表10CO-X-9410ｺﾈ

viOptions Name Type Code No. Q’ty Remarks FSV-2400-10 - With CP10-04501, FP03-06201, FP10-02202, Dust cover & 10S5207 (10 m cable) Monitor Unit F

CODE NO.TYPE略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-3 INSTALLATION MATERIALS工事材料表10CO-X-9408FSV-24/24Sｹｰﾌﾞﾙ（組品）CABLE A

CODE NO.006-922-390-00TYPEFP10-02201略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-2 ACCESSORIES付属品表10CO-X-9501KB直付け金具KB FIXN

CODE NO.006-921-350-00TYPESP10-02602ITEM NO.NAME OF PARTOUTLINEDWG. NO. OR PERSETPERVESSPAREWORKINGQUANTITY REMARKS/CODE NO.BOX NO. P SHIP NO.SP

CODE NO.006-921-340TYPESP10-02601ITEM NO.NAME OF PARTOUTLINEDWG. NO. OR PERSETPERVESSPAREWORKINGQUANTITY REMARKS/CODE NO.BOX NO. P SHIP NO.SPARE

CODE NO.006-921-360TYPESP10-02603ITEM NO.NAME OF PARTOUTLINEDWG. NO. OR PERSETPERVESSPAREWORKINGQUANTITY REMARKS/CODE NO.BOX NO. P SHIP NO.SPARE

D-1

D-2

1-11. MOUNTING THE EQUIPMENT 1.1 Mounting the Hull Unit Note1) The rise/lower control box of the hull unit contains motion sensor. Therefore, never

D-3

D-4

Jan. 28, '03D - 7

Jan. 28 '03Jan. 28, '03D - 8

Takahashi T. Y. HataiD-9

Y. HataiTakahashi T.D-10

D-12