Furuno GP-1850DF User Manual Page 1

INSTALLATION MANUALCOLOR DGPS/PLOTTER/SOUNDERGP-1850DFCOLOR GPS/PLOTTER/SOUNDERGP-1850FSafety Instructions for the Installer ...iE

1-41.3 Installation of TransducersInstalling the inside-hull mount transducerNecessary toolsYou will need the following tools:• Sandpaper (#100)• Sil

1-5Attaching the transducer1. Clean the transducer face to remove any foreign material. Lightly roughen thetransducer face with #100 sandpaper. Also,

1-6Observing the picture1. Press the [POWER] key to turn on the display unit.2. Press the [SNDR] key to select the sounder display.3. Press the soft

1-730°C20101501050.0SNDR FUNCMODE/ FREQSHIFTGAINRANGEDGPS 3D 50kHz32.8SOUNDERFigure 1-10 Video sounder pictureIf the bottom is displayed in red and

1-8Installing the thru-hull mount transducerTransducer mounting locationThis type of mounting provides the best performance of all, since the transdu

1-9 Acceptable transducer mounting locationsDeep-V hull• Position 1/2 to 1/3 length of the hull from stern• 15 to 30 cm off center line (inside first

1-10Procedure for installing the thru-hull mount transducer1. With the boat hauled out of the water, mark the location selected for mountingthe trans

1-11Installing the transom mount transducerThis type of mounting is very commonly employed, usually on relatively small I/Oor outboard boats. Do not u

1-12M5 x 20No. 1M5 x 145°TapeM5 x 20Figure 1-17 Transom mount transducer, mounting flush with hullInstalling the transom mount transducer projecting

1-13Triducer 524ST-MSD, 525ST-MSDThe triducer is designed for thru-hull mounting.Mounting considerationsWhen selecting a mounting location keep the fo

C 9-52, Ashihara-cho, Nishinomiya, Japan Telephone: 0798-65-2111 Telefax: 0798-65-4200 Your Local Agent/Dealer All rights re

1-141.4 Installation of SensorsTransom mount water temperature sensorT-02MTB• Fix the cable at a convenient location with cable clamp.• When the cabl

1-15Thru-hull mount water temperature sensorT-02MSB, T-03MSB• Select a mid-boat flat position. The sensor does not have to be installed per-fectly per

1-16Through-hull mount water temperature/speed sensorST-02MSB, ST-02PSBSelect a suitable mounting location considering the following:• Select a mid-b

2-12. WiringAll wiring are terminated at the rear of the display unit.ANT XDRTEMP/SPDDGPSNMEA+ GND1 32-12 - 24VDCAntenna unitGPA-018iGP-1850DFjGPA-0

2-2Antenna unitConnect the antenna cable to the ANT connector.TransducerConnect the transducer cable to the XDR connector.Water temperature/speed sen

2-3Extending antenna cable lengthThe standard cable is 10m long. For extension, in case of the GPA-016, GPA-018and GPA-018S, an antenna cable set of 1

2-4How to attach the N-P-8DFB connectorOuter SheathArmorDimensions in millimeters.Inner Sheath ShieldRemove outer sheath and armor by the dimensions

3-13. Initial Setting3.1 NMEA SettingNMEA port1. Press the [MENU] key.2. Press the software key labeled "CONFIGURATION".3. Press the softwar

3-2DGPS port1. Press the [MENU] key.2. Press the software key labeled "CONFIGURATION".3. Press the software key labeled "SETUP NMEA/DGP

3-33.2 Output Data SentencesSelect output data sentences for external equipment as follows.1. Press the [MENU] key.2. Press the software key labeled &

iiiiiiiiiiiiiiGround the equipment toprevent electrical shockand mutual interference.Confirm that the power supply voltageis compatible with the volta

3-43.3 Antenna Height1. Press the [MENU] key.2. Press the software key labeled "GPS/DGPS/TD OPTIONS".3. Press the software key labeled "

3-54. Confirm that "ON" is selected at "DGPS MODE" field for GP-1850DF.5. Select "BEACON BAUD RATE" by the arrow key.6.

3-64. Select "BEACON FREQUENCY" by the arrow key.5. Press the software key labeled "EDIT" to display the following message.BEACON

3-73.7 External Equipment Setup (Option)This section shows you how to set up the GP-1850F/1850DF when external equip-ment is connected. If a water tem

3-8Speed AdjustmentAdjust speed when you select own speed source "OWN PDDWHL".1. Press the [MENU] key.2. Press the software key labeled &quo

3-9RETURNEDITDISPLAYSETUP2s SPEED SOURCE GPSTEMP SOURCE OWN XDCRTEMP GRAPH OFFZOOM MARKER OFFSPEED ADJ. +00%TEMP ADJ. +00.0°FDEPTH ADJ. +0.0ftSPD12.3k

3-103.8 Selecting the Echo Sounder Output PowerThe echo sounder output power can be selected for 600 W (for transducer 520-5PSD, 520-5PWD, 520-5MSD) o

3-11Binding screwsM3x10, 10 pcs.NutsNut, washerCover assemblyPanel/chassis assemblyConnector gasketFigure 3-15 Removing cover assemblyWARNINGDo not c

3-126. Remount the cover assembly.Note: Confirm that the following parts are attached:• Inside of the cover: Shield gaskets, GN gasket (See Figure 3-1

4-14. Installation of DGPS Beacon Receiver(for GP-1850F)The DGPS beacon receiver GR-7000A can be incorporated in the GP-1850F to provide itwith DGPS c

iiEquipment ListsStandard supply.oNemaNepyT.oNedoCytQskrameR1tinuyalpsiDE-F0581-PG-1F0581-PGrofE-FD0581-PG- FD0581-PGrof2tinuannetnA710-APG-1F0581-PG

4-2DisassemblyProcedure1. Turn off the power. Wait at least one minute before opening the cover, to allowcapacitors to discharge.2. Remove nuts attach

4-3Installation of DGPS receiverProcedure1. Dismount chassis assembly from panel/chassis assembly by disconnecting theconnector and PH8P from J8 on MA

4-4 Handling of Coaxial Cable• Do not touch the connector with bare hands;use gloves.• Use radio pincers to remove, and pull outstraightl

4-57. Wire cable assembly as shown in the figure below.Reattach this tape asshown right after the DGPS connection.To J8 ofANLG BoardGN-7707J1GR-7000AJ

4-68P connectorto J8Aview6P connectorto J7J7J8PanelAssemblyConnectorMAIN Board14P0311BPanel assemblyANLG Board14P0313BAFigure 4-8 Attaching chassis as

4-7GN gasketShield gasketsFigure 4-10 Inside of the coverChecking the DGPS installation1. Press the [MENU] key.2. Press the software key labeled "

AP-1 APPENDIX TRIDUCER 525ST-PWC/PWD This appendix provides a copy of the installation instructions for AIRMAR triducer. If you loose the original su

APPENDIX TRIDUCER 525ST-PWC/PWD AP-2 P66 Installation templatefor starboard side of boatDrill at locations labeled "B"for the following t

APPENDIX TRIDUCER 525ST-PWC/PWD AP-3 Figure 5. Sensor angle adjustment on transom11° transom angle NO SHIM12-18° transom angle NO SHIM2°-10° transom

iiiOptional equipment (con't).oNemaNepyT.oNedoCskrameR9tinuannetnAS810-APG264-140-000FD0581-PGrof610-APG635-140-000F0581-PGrofS910-APG455-140-000

4-8Connecting DGPS beacon receiverA DGPS beacon receiver whose output format is RS-232C can be connected tothe GP-1850F.Below is the example of interc

ivSystem ConfigurationThe GP-1850F/1850DF mainly consists of a display unit, a GPS antenna and adual frequency transducer. A DGPS beacon receiver is

1-11. Installation of Standard Equipment1.1 Installation of Display UnitMounting considerationsThe display unit can be installed on a tabletop, on the

1-2Mounting procedureFollow the procedure below to mount the display unit on a tabletop or the over-head.Tabletop, overhead mounting1. Fix the hanger

1-3Flush mountPan head screws Cutout for flush mount242 0.55089 0.5147 0.56-R2.25244 1143 115 0.5238 1Figure 1-3 Flush mounting of disp