Furuno Sc 50 User Manual

THD SATELLITE COMPASSSC-50

SP - 2 E7251S01B 4.3 Waterproofing Antenna Unit IPX6 Display Unit IPX5 Processor Unit IPX0 4.4 Vibration IEC 60945 5 COATING COLOR 5.1 Disp

IN-1INDEX A Alarms menu... 2-6 B Battery replacement ... 3-8 C Compass display...

1-11 INSTALLATION 1.1 Mounting Considerations 1.1.1 Antenna unit General • Keep the length of the antenna cable in mind when selecting a mounting

1. INSTALLATION 1-2 • The horizontal separation between the antenna and masts must be as follows: Mast diameter Separation distance (minimum) 10 c

1. INSTALLATION 1-3 Radar AntennaSC-series AntennaBridgeReception blocked by mast.Location influencedby reflected wave. Example of antenna installed b

1. INSTALLATION 1-4 1.2 Installing the Antenna Unit 1.2.1 Antenna unit SC-303 Note: “Bird-repellent fixtures” (supplied) may be attached to the ant

1. INSTALLATION 1-53. Coat exposed parts of nuts, bolts and washers with silicone sealant. RadomebaseCoat withsilicone sealant.Platform Coating bolt

1. INSTALLATION 1-6 8. Set the “cable cover” to the antenna base as shown in the figure below. Cable Cover How to insert the cable cover Insert slot

1. INSTALLATION 1-71.2.2 Antenna unit SC-603 Note: “Bird-repellent fixtures” (supplied) may be attached to each antenna element and the Antenna Cove

1. INSTALLATION 1-8 4. Making sure each antenna element is correctly oriented, fix each with its nut. Write the corresponding arm number on each coa

1. INSTALLATION 1-97. Orient the antenna unit as shown in the illustration below. PORTAntennaElement1AntennaElement 2AntennaElement3A number is in

The paper used in this manualis elemental chlorine free. Your Local Agent/Dealer Your Local Agent/Dealer9-52 Ashihara-cho,9-52 Ashihara-cho,Nishinomiy

1. INSTALLATION 1-10 Welding the antenna unit The antenna unit may be welded to the antenna mast if the satellite status display shows “OK.” 1. Unf

1. INSTALLATION 1-117. Make a loop in the antenna cable as shown in the illustration below. Fasten the antenna cable to the antenna mast with cable

1. INSTALLATION 1-12 1.3 Installing the Processor Unit The processor unit should be mounted aligned with the ship’s fore-and-aft line. It can be mou

1. INSTALLATION 1-131.3.2 Deck mount Orient the processor unit as shown below and fix it to the mounting location with four tapping screws (M5x20). Y

1. INSTALLATION 1-14 1.3.3 Installation on the underside of a desk The processor unit may be mounted on the underside of a desk as shown in the figu

1. INSTALLATION 1-151.4 Installing the Display Unit 1.4.1 Desktop, overhead mounting 1. Fasten the hanger to the mounting location with four tappi

1. INSTALLATION 1-16 Flush mount “S” Flush mount “S” kit Type: OP20-17, Code No.: 000-040-720) Name Type Code No. Qty Flush Mount Fixture 20-00

1. INSTALLATION 1-171.5 Wiring This section covers general wiring. For further details see the interconnection diagram at the back of this manual. DI

1. INSTALLATION 1-18 Note 1: Use cable type DPYC-1.5 (or equivalent) for the power cable. ConductorS = 1.5 mmφ = 1.56 mm2DPYC-1.5ArmorSheathφ = 11.7

1. INSTALLATION 1-19How to attach connector N-P-8DFB Outer Sheath50301510ArmorInner Sheath ShieldCover with heat-shrink tubing and heat.Cut off ins

iSAFETY INSTRUCTIONSWARNINGWARNINGTurn off the power at the switchboardbefore beginning the installation.Fire or electrical shock can result if thepo

1. INSTALLATION 1-20 1.6 Initial Settings Follow the procedures in this section to enter initial settings. NOTICEImproper menu settings may stop outp

1. INSTALLATION 1-211.6.2 Choosing mounting method 1. Turn on the processor unit and then press the [MENU] key to show the menu. MAIN MENUSATELLITE

1. INSTALLATION 1-221.7 Connection of External Equipment 1.7.1 General wiring All external equipment are terminated on the MAIN Board inside the pro

1. INSTALLATION 1-231.7.2 Fabrication of cables Cable Sectional view, fabrication Power cable DPCY-1.5 (or equivalent) ConductorS = 1.5 mmφ = 1.56

1. INSTALLATION 1-24 (This page intentionally left blank.)

2-12 OPERATION 2.1 Controls MENUENTDISPDIMHDGSETUPSATSTATUSSATELLITECOMPASSOmnipad: Selects menu items; shifts cursor. MENU key: Opens

2. OPERATION 2-2 2.2 Turning the Power On/Off Use the power switch on the processor unit to turn the power to the display unit on and off. POWERSwit

2. OPERATION 2-32.4 Choosing a Display Use the [DISP] key to show a display desired. 2.4.1 Description of displays Heading display The heading disp

2. OPERATION 2-4 Steering display The steering display shows heading in digital and analog form. SOG and COG are also indicated. Note that COG accura

2. OPERATION 2-5Speed display Depending on the setting of DISTANCE DISP on the TRIP menu, the Set and Drift display or the Distance Run display is sh

ii TABLE OF CONTENTS FOREWORD ...iv

2. OPERATION 2-6 2.5 Alarm Setup The SC-50 can alert you with audible and visual alarms when GPS signal, DPGS signal and WAAS signal are lost. To set

2. OPERATION 2-72.6 Confirming Satellite Status You can check the receiving condition of each antenna unit as follows: 1. Press the [MENU] key to

2. OPERATION 2-8 2.7 GPS Setup The GPS SETUP menu smoothes position and course, averages speed, applies position offset, and deactivates unhealthy sa

2. OPERATION 2-9DISABLE SV (Disable satellite) Every GPS satellite is broadcasting abnormal satellite number(s) in its Almanac, which contains genera

2. OPERATION 2-10 5. Choose SENTENCE and then press the [ENT] key. DATA OUT1HDT VTG VHWHDM GGA VBWROT GNS HVEATT GLL ZDAVDR DATA OUT1 menu, senten

2. OPERATION 2-1111. Use the Omnipad to choose the baud rate of the equipment connected and then press the [ENT] key. 12. INTERVAL is selected; press

2. OPERATION 2-12 Output sentence limitation The number of sentences which can be output depends on baud rate and output interval settings. The maxim

2. OPERATION 2-132.8.2 Log pulse This equipment provides SOG (speed over ground) in high accuracy. It converts an SOG value to a pulse signal and out

2. OPERATION 2-14 2.9 System Setup 2.9.1 Geodetic data Your unit is preprogrammed to recognize most of the major chart systems of the world. Although

2. OPERATION 2-152.9.2 Units of measurement Distance/speed can be displayed in nautical miles/knots, kilometers/kilometers per hour, or miles/miles p

iii2.9.4 Time format... 2-15 2.9.5 Demonstr

2. OPERATION 2-16 2.9.5 Demonstration mode The demonstration mode provides simulated operation of the equipment. 1. Press the [MENU] key to open th

2. OPERATION 2-172.10 WAAS/DGPS Setup 1. Press the [MENU] key to open the menu. 2. Choose WAAS/DGPS and then press the [ENT] key. WAAS/DGPS MODE :

2. OPERATION 2-18 2) Use the Omnipad to choose WAAS satellite search method, AUTO or MANUAL as appropriate. For MANUAL, press the [ENT] key, enter a

2. OPERATION 2-193) FREQ is selected; press the [ENT] key. 4) The cursor is selecting the hundredths digit so press ▲ or▼ to display appropriate di

2. OPERATION 2-20 2.11 OTHERS Menu The OTHERS menu contains the following items: HOLD HDG DATA: Choose whether to display last-used heading data at

2. OPERATION 2-212.12 TRIP Menu The TRIP menu functions to • Choose the indication to show on the SOG/STW display • Choose source of distance run • R

2. OPERATION 2-22 2.13 Resetting Distance Run The distance run may be reset to zero as below when the source of distance run is GPS or VBW. 1. Pre

3-13 MAINTENANCE, TROUBLESHOOTING WARNINGELECTRICAL SHOCK HAZARDDo not open the equipment.Only qualified personnelshould work inside theequipment. 3

3. MAINTENANCE, TROUBLESHOOTING 3-2 3.2 Troubleshooting This section provides basic troubleshooting procedures which the user may follow to restore n

3. MAINTENANCE, TROUBLESHOOTING 3-33.3 Diagnostics Diagnostic test1 The diagnostic test1 checks the equipment for proper operation. Note: Heading is

iv FOREWORD A Word to the Owner of the SC-50 FURUNO Electric Company thanks you for purchasing the FURUNO SC-50 THD Satellite Compass. (Hereafter, f

3. MAINTENANCE, TROUBLESHOOTING 3-4 AD-10 IECOUT1 - - - -OUT2 - - - -OUT3 - - - -OUT4 - - - -OUT5 - - - -OUT6 - -SOFTWARE VERSION

3. MAINTENANCE, TROUBLESHOOTING 3-5Diagnostic test2 If the heading indication changes randomly when ship is at anchor or does not change when the shi

3. MAINTENANCE, TROUBLESHOOTING 3-6 Diagnostic test3 This test checks the buzzer signal/contact for proper operation. 1. Press the [MENU] key to op

3. MAINTENANCE, TROUBLESHOOTING 3-73.4 Program Number You may display the program number as follows: 1. Press the [MENU] key to open the menu. 2.

3. MAINTENANCE, TROUBLESHOOTING 3-8 3.6 Replacement of Battery The processor unit has a battery which stores data when the power is turned off. When

3. MAINTENANCE, TROUBLESHOOTING 3-93.7 Replacement of Fuse The 3 A fuse on the POWER Board inside the processor unit protects the equipment from over

3. MAINTENANCE, TROUBLESHOOTING 3-10 Error messages (con’t from previous page) Error Message Meaning Remedy BATTERY ALM! Voltage of battery in pro

AP-1APPENDIX 1. Menu Tree SATELLITEMESSAGESMENUALARMSBUZZER (SHORT, LONG, CONSTANT)DGPS (OFF, ON)GPS SETUPSMOOTH POS (0 SEC)SMOOTH S/C (5 SEC)LAT O

APPENDIX AP-2 2. Digital Interface Output sentences of channel 1 DATA OUT1-5: HDT, HDM, ROT, Patt, Phve, VTG, GGA, GLL, GNS, ZDA, VHW, VBW, VDR DAT

APPENDIX AP-3Schematic diagrams Data IN Load requirements Isolation: Optocoupler Input Impedance: 440 ohm Max. voltage: ±15V Data Out 1-6 Outp

vSYSTEM CONFIGURATION The SC-50 consists of an antenna, a display unit and a processor unit. The tri-antenna system accommodates three antennas/receiv

APPENDIX AP-4 Data sentences PFECatt- True heading, pitching, rolling $PFEC,GPatt,xxx.x,+xx.x,-xx.x<CR><LF> (Ver. 1.5) $PFEC,GPatt,xxx.x,

APPENDIX AP-5GNS - GNNS fix data $--GNS,hhmmss.ss,llll.lll,a,yyyyy.yyy,a,c--c,xx,x.x,x.x,x.x,x.x,x.x*hh<CR><LF> |

APPENDIX AP-6 VBW - Dual ground/water speed $--VBW,x.x,x.x,A,x.x,x.x,A,x.x,A,x.x,A*hh<CR><LF> | | | | | |

APPENDIX AP-7VLW - Distance travelled through the water The distance travelled, relative to the water. $--VLW,x.x,N,x.x,N*hh<CR><LF>

APPENDIX AP-8 3. Input/Output Ports Port Label Terminal Name I/O Signal Remarks DATA OUT1 WAGO 231-304/026-000 O DATA OUT2 WAGO 231-304/026-000 O

APPENDIX AP-9 Port Label Terminal Name I/O Signal Remarks DATA OUT6 WAGO 231-304/026-000 O HeadingAD-10 only AD-10 output interval: 25ms LOG Signa

APPENDIX AP-10 4. Parts List and Parts Location This equipment contains complex modules in which fault diagnosis and repair down to component level a

APPENDIX AP-11F U R U N OModel SC-50/110Unit SC-502DISPLAY UNITELECTRICAL PARTS LIST Ref.Dwg. PageBlk.No.SYMBOL TYPE CODE No. REMARKS SHIPPABLEASSEMB

APPENDIX AP-12 5. Geodetic Chart Codes 001：WGS84 002：WGS72 003：TOKYO ：Mean Vallue (Japan, Korea, and Okinawa) 004：NORTH AMERICAN 1927 ：Mean Vallue

APPENDIX AP-136. Principle of Satellite Compass Own ship's heading can be determined by decoding the data in the carrier frequency in addition t

vi EQUIPMENT LIST Standard supply Name Type Code No. Qty Remarks SC-303  Radome type GPS Antenna SC-603  Choose one Open type Display Unit SC

APPENDIX AP-14 7. What is WAAS? WAAS, available in North America, is a provider in the worldwide SBAS (Satellite Based Augmentation System) navigatio

ＰＡＣＫＩＮＧ ＬＩＳＴ20AY-X-9854 -3 SC-303N A M EO U T L I N EDESCRIPTION/CODE №Q'TY1/1ユニット UNITGPSｱﾝﾃﾅGPS ANTENNASC-303000-041-9251工事材料 INSTALLATION MATE

A-2

CODE NO.CODE NO.CODE NO.CODE NO.004-379-660TYPETYPETYPETYPECP20-02260略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-0 INSTALL

CODE NO.CODE NO.CODE NO.CODE NO.004-377-570TYPETYPETYPETYPECP20-02201略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-1 INSTALL

CODE NO.004-377-590TYPECP20-02202略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-4 INSTALLATION MATERIALS工事材料表20AT-X-9404ｽﾘｰﾎﾞ

ＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴ20AY-X-9851 -0 SC-502-J/ESC-502-J/ESC-502-J/ESC-502-J/EN A M EO U T L I N EDESCRIPTION/CODE №Q'TY

CODE NO.CODE NO.CODE NO.CODE NO.004-380-660TYPETYPETYPETYPECP20-02203略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-0 INSTALL

ＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴ20AY-X-9852 -1 SC-501-J/ESC-501-J/ESC-501-J/ESC-501-J/EN A M EO U T L I N EDESCRIPTION/CODE №Q'TY

CODE NO.CODE NO.CODE NO.CODE NO.004-380-560TYPETYPETYPETYPECP20-02601略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-1 INSTALL

SP - 1 E7251S01B THD SPECIFICATIONS OF THD SATELLITE COMPASS SC-50 1 GENERAL 1.1 Heading Accuracy ±1.0° (95%) 1.2 Heading Resolution 0.1° 1.3

CODE NO.CODE NO.CODE NO.CODE NO.004-379-720TYPETYPETYPETYPESP20-01101ITEM ITEM ITEM ITEM NO.NO.NO.NO.NAME OF NAME OF NAME OF NAME OF PARTPARTPARTPARTO

CODE NO.CODE NO.CODE NO.CODE NO.000-041-405TYPETYPETYPETYPEOP20-29 略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-0 20AY-X-

CODE NO.CODE NO.CODE NO.CODE NO.000-040-720TYPETYPETYPETYPEOP20-17 略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-0 20AY-X-

Takahashi T. Y. HataiD-1

Takahashi T. Y. HataiD-2

Takahashi T. Y. HataiD-3

Takahashi T. Y. HataiD-4

Y. HataiD-5

Y. HataiD-6

相互結線図INTERCONNECTION DIAGRAMDCBA654321FURUNO ELECTRIC CO., LTD.kgDRAWNCHECKEDAPPROVEDSCALEMASSDWG No.TITLENAME名称サテライトコンパスGND1234567+15VSHIELDDISPLAYMJ