Furuno FR-2135S User Manual

Back

1-2Installation precaution for S-band scanner unitIf an S-band scanner unit is mounted near the end of a platform to provide suffi-cient rotation cle

1-3How to lift scanner unit1. Fix the scanner radiator to the scanner unit chassis.2. Attach the lifting fixtures and collars as shown in Figure 1-2

1-4Scanner unit assemblingThe scanner radiator and the scanner housing are shipped in separate packages.Assemble them as below. The scanner unit may

1-5Fastening the scanner unit to the mounting platformSee the figure on the next page for scanner unit mounting.1. Referring to the scanner outline d

1-6Seal washerCorrosion-proofrubbermatCoat with silicone sealant afterfastening ground wire.Ground wireScanner bodyHex boltHex nutORGround wireCoat w

1-71.2 Display UnitBefore mounting the display unitIf Gyro Converter GC-8 (option) is to be used, install and setup the GYRO CON-VERTER Board before

1-84. While one person is holding the mounting base at the sides, pull the handle onthe underside of the control head to draw the display unit toward

1-9CatchStopperStayFigure 1-10 Setting catch to hole in stayc)Release hand from stopper.Release stopper;fix stay.Figure 1-11 Stay fixed6. Fasten the

1-10J106J105J104J103J446J466J462J465*M3x8, 5 pcs.****Slide forward.M4x8, 2 pcs.Fixing hole (front)Fixing hole (rear)KnobFigure 1-12 How to remove th

1-11Separate type control head kit (Type: OP03-151, No.: 008-485-530)emaNepyTytQ.onedoCskrameR.yssAelbaCP1/P02BS642LU1218-041-0002249S30,m01teeFrebbu

Your Local Agent/DealerYour Local Agent/Dealer9-52 Ashihara-cho,9-52 Ashihara-cho,Nishinomiya, JapanNishinomiya, JapanTelephone :Telephone : 0798-65-2

1-124. Unfasten the M4 screw fixing the ground terminal of the connection cable.5. Push the monitor forward until you hear a click.6. Unscrew four sc

1-13Control head modification procedure1. Unfasten eight screws (M4X8) on the underside of the control head. Unplugconnectors P314, P312 and P317 fro

1-14Connection of display unit to control head1. Attach the handle to the handle plate, using the screws for the handle andbottom cover of the contro

1-151.3 Power Supply UnitThe Power Supply Unit PSU-004 does not contain usual operating controls. There-fore, it can be installed in any recessed pl

This page is intentionally left blank.

2-1WIRING2.1 Display UnitFabricating the power cable DPYCY-3.5 (JIS cable)1. Remove the vinyl sheath by 80 mm.2. Cut off jute tape wrapped around the

2-2Leading in cables to the display unitThe cable clamp may be positioned inside the display unit (default arrangement),outside the display unit or a

2-3Cable fed from outside display unit(B) Power clamp(Aluminum)(C) Signal clamp(Aluminum)(D) Rear clamp plate(A) Rear clamp baseBottom clamp front pl

2-4ConnectionsOpen the display unit and fix it with the stay. (For procedure see page 1-6.) Re-move the shield cover from the INT Board. Connect sign

2-5Connectors on the INT BoardTable 2-1 Connectors on the INT BoardemanlangiSnoemaNbcprotcennoC.onrotcennoCepytelbacilppAtnempiuqeskrameRlangiStupnIl

iSAFETY INSTRUCTIONSWARNINGWARNINGRadio Frequency RadiationHazardThe radar scanner emits electromagneticradio frequency (RF) energy which can beharmf

2-6How to attach NH connector20mm1 Insert NH connectorwire into NH connectorhousing.2 Cut shrink tubingin 20 mm lengths andslip onto each wire.3 Sold

2-73. Open the left side cover on the scanner unit with the hex wrench (supplied).4. Unfasten the cable gland for the multicore cable and remove the

2-89. Remove the sheath of each conductor by 6 mm. Fix crimp-on lugs (FV1.25-4,blue, ø4) to each conductor. Make sure each connection is secure both

2-9Terminal board fixing plate for RTB-801 Ground terminalFigure 2-13 Scanner unit, rear viewLocking wire saddleFigure 2-14 Scanner unit, rear view19

2-1020.Route the signal cable beneath the lower left side of the terminal board fixingplate for the RTB-801. Shorten conductors of the signal cable c

2-1126.Check for miswiring, loose screws. Grease the fixing bolts for the cover, gas-ket, and tap holes in the scanner chassis. Attach the cover.When

2-122.4 Power Supply UnitWire the unit as shown in the interconnection diagram.Thermal relayK2Relay K3Relay K1TBPTB12TBPTB13TBPTB11TBPTB14Photo No. 3

3-1INITIALIZATION AND ADJUSTMENT3.1 Tuning InitializationTune the radar as follows: Press [RADAR MENU] [0] [0] [2] [0] [0] [0] [0] (TUNEINITIALIZE on

3-23.4 Heading AlignmentYou have mounted the scanner unit facing straight ahead in the direction of thebow. Therefore, a small but conspicuous target

3-33.5 Adjusting Sweep TimingSweep timing differs with respect to the length of the signal cable between thescanner unit and the display unit. Adjust

iiCAUTIONObserve the following compass safedistances to prevent deviation of amagnetic compass:Ground the equipment toprevent electrical shock andmutu

3-43.7 Confirming Magnetron Heater VoltageMagnetron heater voltage is adjusted at the factory. Confirm that magnetron heatervoltage is within the pre

3-5PCB 03P9243P801VR1Figure 3-7 Scanner unit, stern side view3.8 Initial Setting MenusThe INITIAL SETTING menu (four menus) and the OWN SHIP INFORMATI

3-6[INITIAL SETTING 1]1 [FUNCTIONS(4)]2 HL ALIGNEBL 0.0°3 TIMING ADJVRM 00.004 ANT HGT 5m/7m/10m/15m/20m/30mMORE5 LOG PULSE 200P6 [OWN SHIP INFORMATIO

3-7OWN SHIP INFORMATION: Enter ship's characteristics; length, width, radarscanner position, navigation antenna position, turn rate, and speed ra

3-8INITIAL SETTING4 menuKeying sequence: [RADAR MENU] [0] [0] [0] [2] [0] [0] [0]MODEL: Selects radar model.TYPE: Selects specification of radar. Sele

4-1INSTALLATION OF OPTIONAL EQUIPMENT4.1 Gyro Converter GC-8The Gyro Converter GC-8, incorporated inside the radar display unit, convertsanalog gyroc

4-24) Connect the GYRO CONVERTER Board to the INT Board (cables suppliedwith GC-8) as shown below.INT Board GYRO CONVERTER BoardJ446

4-3Connection of external power supplyAn external power supply is necessary when the repeater signal is step-by-steptype and the step voltage is belo

4-4Setting method 1: by gyrocompass specifications1) Gyrocompass type 2) FrequencyGyrocompasstypeSW1-4SW1-5SW1-6JP1 Frequency SW1-7SW1-8RemarksAC syn

4-5Setting method 2: by make and model of gyrocompassrekaMsledoMnoitacificepSWS1-1WS2-1WS3-1WS4-1WS5-1WS6-1WS7-1WS8-1WS1-2WS2-2WS3-21PJ2PJ3PJ4PJ5PJON

iiiTABLE OF CONTENTSEQUIPMENT LISTS...ivSYSTEM CONFIGURATION...

4-6Location of DIP switches, jumper wires on the GYRO CONVERTERBoard64P1106JP5, JP4(Supply voltage)JP2(Rotor voltage)JP3(Stator voltage)JP1(Gyro type

4-74.2 ARP Board ARP-26The ARP Board ARP-26, which provides ARPA functions, is an optional circuitboard which is accommodated in the display unit of

4-8ARP board adjustment1. Turn the GAIN, A/C SEA and A/C RAIN controls fully counterclockwise, andthen transmit on the 12 nm range.2. Connect a digit

4-9Final checkConnect a gyrocompass and a log to the radar and place the radar under transmitstate. Confirm that LEDs CR9, CR10, CR11, CR12, CR15 and

4-104.3 RP Board RP-26The RP Board RP-26, which providesvideo plotter functions, consists of a circuitboard and a card drive both of which are accomm

4-114. Unfasten the front panel from the display pedestal.5. Pass the connector from the card case through the hole in the display pedestal.Display p

4-1210.Fasten the front panel on the display pedestal.11.Retract the stay to close the display unit.12.Fasten the right arm cover.Separate type contr

4-13M-card baseM-cardcase lidPan Head ScrewM2.6X5(2 pcs.)Display pedestalDisplay pedstalfront panelFigure 4-13 Display pedestal, front view5. Loosen

4-1410.Fasten the front panel of the display pedestal.11.Fasten the ground wire to the location shown in Figure 4-14.12.Close the monitor.4.4 Perform

4-154.5 Alarm KitNecessary parts: OP03-156 (Code no. 008-500-650)The alarm kit mainly consists of a circuit board and connection cables, and pro-vide

ivEQUIPMENT LISTSStandard SupplyemaNepyT.oNedoCytQskrameRtinUrennacSFA03NS-1rotaidaRFA63NS-6200-BSR-1reciedtuohtiwrohtiw,sissahcannetnA1300-BSR-8800-

4-16J475J474J473J472J471J451AAPan-head ScrewM3X8, 4 pcs.Cable Tie CV-100,2 pcs.ALARM Board03P9262NH Connector03-1991(3P), 4 pcs.Pan-head screwM4X12 C

vOptional EquipmentemaNepyT.oNedoCytQskrameRyalpsiDetomeR0108-DMF–1retrevnoCoryG2-8-CG025-644-800tes1redroetarapeShctiwsretnI7-JR–1hctiwsretnI8-JR–1r

viSYSTEM CONFIGURATIONDISPLAY UNITRDP-124ARPA BoardARP-26NavigatorIEC 61162-1 (Input/Output)IEC 61162-1 (Input)Speed LogOPTIONPerformanceMonitorPM-5

1-1MOUNTING1.1 Scanner UnitMounting considerations• The scanner unit is generally installed either on top of the wheelhouse or on theradar mast, on a