Furuno FS-1503 User Manual

1-31.2 Mounting of Antenna CouplerThe antenna coupler is installed between the antenna and the transceiver, and tunes the antennato the transmitter.Mo

1-4Mounting the antenna couplerMounting methodsThe antenna coupler can be fixed to the floor, bulkhead, or on the overhead. For mounting onthe bulkhea

1-5How to mount the antenna couplerWire clipLead-ininsulatorStand-offinsulatorINDOOR INSTALLATIONFrom antenna selectorANTENNA SELECTORFor thin bulkhea

1-61.3 Ground SystemA good antenna can work well only when it is connected to an efficient rf ground. Without agood ground system, the full potential

1-71.4 Mounting of AntennaAbout antennasThe antenna plays the most important role in radio communication. If it cannot receive ortransmit effectively

1-8Typical antenna installationsShip stationOn ship stations, the long wire antenna is spannedbetween supporting structures. The length of thehorizont

2-12. WIRINGSpeaker(option)Control CableCoax.CableTotal length ofantenna shouldbe 6 to 15 meters.Handset(option)DSC TerminalNBDP TerminalRemote Statio

2-27654321GRNYELORGREDBRNBLKWHTDUMMYTHRUNC (IANT)BUSYTUNEGND+12 VLeave slack in wiresto prevent breakage.Antennawire7654321TB2TB1Coaxial cableCopper s

3-13. WIRING OF OPTIONAL EQUIPMENT3.1 NBDP Terminal DP-6The NBDP Terminal connects to the REMOTE connector on the FS-1503. It has a remotecontrol func

3-23.3 Remote Station RB-500Connect to the REMOTE connector on the FS-1503. If more than two RB-500s or DSC, NBDPare to be installed, connect them via

C 9-52, Ashihara-cho, Nishinomiya, Japan Telephone: 0798-65-2111 Telefax: 0798-65-4200 Your Local Agent/Dealer All rights re

3-33.5 REMOTE and CONTROL BoardsCOVERGASKETSHIELDCOVERPAN HEAD SCREWM3X6 (9 PCS.)HANGER GASKETBINDING SCREWM4X10 (6 PCS.)J4J5J3TX/RX BOARD05P0666CONTR

3-43.6 BK (Break-in) ConnectionBK (Break-in) connection is necessary when the FS-1503 is installed together with an HFreceiver or transceiver. The BK

3-53.8 SW Regulator (SW REG board)The FS-1503 is supplied with negative ground. If necessary, to float the battery negative line,the SW REG Kit is ava

3-63.9 Dummy LoadThe dummy load enables testing of the two-tone alarm. Install the board following the figurebelow. CHANGE SYSTEM SETTING 9917 to 1.JT

3-73.10 Floating Ground Radiotelephone (FS-5000, etc.)Connect the FS-1503 to the floating ground radiotelephone with a connection cable whosediameter

4-14. INSTALLATION CHECK4.1 lnstallation ChecksAfter completing the installation, check the FS-1503 and all equipment connected to it forproper connec

4-2PerformanceIf no problems were found in the preceding sections, then turn on the transceiver and check itfor proper performance.Receiver1. Turn on

iiiiiiiiiiiii iSAFETY INSTRUCTIONSDANGERNever touch the SSB antenna, antennacoupler or lead-in insulator when theSSB radiotelephone is transmitting.Hi

iiTABLE OF CONTENTSEQUIPMENT LISTS ...iiiSYSTEM CO

iiiEQUIPMENT LISTSStandard SetemaNepyT.oNedoCytQskrameRtinUreviecsnarT3051-SF—1 elbacrewophtiWA3051-SF— A.S.UroFrelpuoCannetnA3051-TA—1seirosseccA0-50

ivOptional EquipmentemaNepyT.oNedoCytQskrameRrewoPCD-CA072-RP—1retrevnoCCD-CD022-CP—1tiKA-ETOMER28-50PO018-939-5001roFC232-SRtiKB-ETOMER38-50PO0028-93

vSYSTEM CONFIGURATION R0246810SH3EAGC NBSIMPSSB TRANSCEIVER FS-1503MICOFFVOLUME RF GAIN FREQ/CHNBDP TerminalDP-6DSC TerminalDSC-60DistributorDB-120DS

1-11. MOUNTING1.1 Mounting of Transceiver UnitGeneral mounting considerationsThe transceiver unit can be mounted on the overhead, a bulkhead, on a tab

1-2Console mountingMounting considerationsIn addition to the general mounting considerations mentioned on the previous page, keep thefollowing points