Furuno IF-NMEASC User Manual

INTERFACE UNITIF-NMEASCOPERATOR'S MANUALwww.furuno.co.jpMODEL

22. WIRINGOpen the IF unit with your hands, detach the shield cover and connect external equipment, refer-ring to the illustration below and the inter

2. WIRING3Cable construction3Approx. 70ArmorBraided shieldData cable TTYCS-1 or equivalent Data cable TTYCS-4 or equivalentPower cable DPYC-1.5 or eq

43. ADJUSTMENTS3.1 LEDs and Equipment StatusThe six LEDs above the heading indication light, flash or go off according to equipment status.LED state a

3. ADJUSTMENTS53.2 Setting Up NMEA PortsPorts J4 and J5 output data in NMEA 0183 format. Select the data to output from those ports, along with baud

3. ADJUSTMENTS67. Push the [Menu/Cancel] button to light the Bps LED on the Port 2 line.8. Push the [Enter] button. The Bps LED starts flashing and t

3. ADJUSTMENTS713. Push the [+] or [-] button to select desired output interval, referring to the table below.14. Push the [Enter] button. The output

3. ADJUSTMENTS83.3 Heading, Pitch and Roll OffsetsTurn on the IF unit and wait approx. three minutes for the satellite compass to settle. Then, check

94. OPERATIONNormally, no operation is required except to power the unit (from the switchboard). The ST-BY LED on the cover is ON, OFF or flashing acc

105. MAINTENANCE, TROUBLE-SHOOTINGThis chapter provides the information for keeping your unit in good working order.5.1 Preventive MaintenanceRegular

5. MAINTENANCE, TROUBLESHOOTING115.2 Replacing the FuseThe 2A fuse inside the unit protects it from overcurrent and equipment fault. If the power can

5. MAINTENANCE, TROUBLESHOOTING125.4 Self TestThe self tests check the equipment for proper operation.Self test 1This test checks the two GPS receive

5. MAINTENANCE, TROUBLESHOOTING13Self test 2This test checks this unit's processor and output for proper operation.1. With the display showing &

5. MAINTENANCE, TROUBLESHOOTING14This page is intentionally left blank.

FURUNO IF-NMEASC SP - 1 E7265S02A-M SPECIFICATIONS OF INTERFACE UNIT IF-NMEASC 1 INPUT PORT NMEA 2000*, for data I/O between FURUNO satellite com

Jul.23'07 R.EsumiD-1

243A1BC12345678J7NET_SNET_CNET_HアカクロシロアオﾑﾗｻｷキﾐﾄﾞﾘREDBLKWHTBLUPPLYELGRNNET_LSGRDSDFG1234J35FGAD-1012J4TD-ATD-BFG3NMEA12TD-ATD-BFG3NMEAJ5IF-NMEASCインターフェ

This page is intentionally left blank.

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANTelephone :

iIMPORTANT NOTICES• This manual is intended for use by readers with a solid knowledge of English. • No part of this manual may be copied or reproduc

ii SAFETY INSTRUCTIONSWARNINGIndicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.CAUTIONIndicat

SAFETY INSTRUCTIONSiiiCAUTIONCAUTIONObserve the following compass safedistances to prevent interference to amagnetic compass:Turn off the power at the

ivTABLE OF CONTENTSFOREWORD ...vSYSTE

vFOREWORDA Word to the Owner of the IF-NMEASCCongratulations on your choice of the FURUNO IF-NMEASC Interface Unit. We are confident you will see why

viSYSTEM CONFIGURATIONSC-30 12-24 VDC: Standard supply: Local supplyIF-NMEASC INTERFACE UNITRadarCurrent Indicator Scanning SonarOtherNMEA 2000AD-10NM

11. MOUNTING1.1 Equipment List1.2 Mounting ProcedureWhen choosing a mounting location for the unit, keep the following points in mind:• Select a loca