Furuno FSV-84 User Manual

COLOR SCANNING SONARFSV-84www.furuno.co.jp

1-2 Compartment1200 mm 500 mm500 mm500 mm Maintenance space, example sonar compartment Note: After mounting the equipment, be sure to install anti-

1-31.1.2 Shortening the retraction tank Shorten the tank as necessary so that the transducer positions well below the keel when it is fully lowered.

1-4 1.1.3 Remarks for installation of retraction tank 1. Install, if possible, the tank on the keel where the tank can be most firmly fixed. 2. In

1-51.1.4 Installing hull unit on retraction tank After welding the retraction tank and allowing sufficient time for cooling, install the hull unit a

1-6 1.1.5 Installing stays (anti-vibration measure) Install stays from the top of the hull unit to the ship’s hull. The stays should be angle iron w

1-71.2 Processor Unit Mounting considerations When choosing a mounting location, keep in mind the following points: • The processor unit must be mo

1-8 Mounting procedure 1. Unfasten two bolts from the bottom of the front side of the processor unit. Pull the unit toward you to separate it from t

1-9Mounting procedure 1. Drill four holes of 12 mm in diameter in the mounting location, referring to the outline drawing for mounting dimensions. 2

1-10 Attaching the CRT filter 1. Attach two spacers (5×2.5, supplied) with screws (M5×10, supplied) to the location shown below. 2. Screw two hood

1-111.4 Control Unit The control unit is designed for mounting on a tabletop, with or without the KB (keyboard) fixing plate (supplied), which mounts

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANTelephone :

1-12 Control unit coverPrevious cable holeScrewM4x8 (8 pcs.)ClampScrew (M4x12)Fasten the cable with the clamp here.NutSpring washerFlat washerJ1J2Con

1-131.5 Transceiver Unit The length of the cable between the transceiver unit and the hull unit is 5 m, so choose a mounting location within 5 m of t

1-14 1.6 Attachment Kit (option) The attachment kit permits use of the tank for the CSH-80 series. Attachment kit (Type: OP10-30, Code no.: 000-067

1-15Hex. nutSpring washerFlat washerInsulation gasket (2)Insulation gasket (1)Hex. boltRetraction tankHex. boltFlat washerHull unit flangeO ringInsul

1-16 1.7 FRP Tank (option) Caution for installing FRP tank Use an FRP tank supplied by FURUNO. Other makes of tank may be used, however watertightne

1-174. Set the hull unit on the top of the retraction tank, observing the following cautions: - Clean the hull unit flange to make sure no foreign m

1-18 1.8 Control Box Extension Kit (option) The control box may be mounted separately from the hull unit. Detach the control box and mounting plate

1-19Fix the control box to bulkhead with four M10 bolts. GNDTERMINALCABLE CLAMPFIXING HOLETERMINAL

1-20 This page intentionally left blank.

2-12. WIRING 2.1 How to Use the Crimping Tool, Pin Extractor A special crimping tool is necessary for connection of wires to the contact pins of the

iWARNINGDo not install the equipment where itmay get wet from rain or water splash.Water can cause fire or electrical shock, ordamage the equipment.B

2-2 2.2 Wiring Monitor(Local supply)CONTROL UNIT FSV-8401CONTROL UNIT FSV-8401MONITOR UNIT FSV-2400PROCESSOR UNITFSV-8402HULL UNITFSV-8432(800 mm str

2-3Transducer cable If the transducer cable is not quite long enough, unfasten the cable clamp shown in the figure below to release the cable. This w

2-4 2.3 Monitor Unit (option) 2.3.1 Fabrication of cable from processor unit One of the cables 10S2074 (10 m) or 10S2075 (30 m) runs between the

2-5HousingClampWasherNutCenter PinGasket7.5Shield3Positioning guide pins Guide pins of the connector identify the mating receptacle. They are; • G

2-6 Assembling D-SUB connector (CN-A302) 1. Remove vinyl sheath of cores by 3 mm. 2. Pass the cores through shrink tubing (local supply). 3. Solde

2-7Cable coverCable from processor unit(10S2074 or 10S2075) Cable from control unit(10S2076)ClampConnector boardCN-A306CN-A305 CN-A30434521CN-A308 CN

2-8 2.4 Processor Unit Cables from the monitor unit, transceiver unit and other equipment are connected to the CONE Board (10P6905) in the processor

2-92.4.1 Cable from transceiver unit This cable (10S1258) runs between the processor unit and transceiver unit (FSV-841). Pass it through the cable

2-10 Positioning guide pins Guide pins of the connector identify the mating receptacle. They are; • Guide pin A (Large): 1 • Guide pin B (Small)

2-112.4.5 Optional equipment Optional equipment (navigator, current indicator, AD converter, speed log, etc.) are connected at the rear of the proces

ii CAUTIONMaximum speed while the transducer isprojected or being raised or loweredis as below, to prevent damage to thetransducer.

2-12 8 cmSoldering sideSoldering-sideConnector caseConnector case1 cm2 cm3 mmShield2 cm3mmShieldVinyl sheathVinyl sheathVinyl sheathArmorSolder unuse

2-13Synchronizing with echo sounder or other sonar To synchronize the transmission of the FSV-84 with an echo sounder or other type of sonar, make co

2-14 2.5 Transceiver Unit 2.5.1 Fabrication of 38P connector 00-8016-038-313761HV (CN-B101) Pass the cable (10S2158) from the processor unit (FSV-84

2-15Power cable fabrication Use power cable DPYCY-2.5 or equivalent. 140 (Power source side: 200)3530FV2-4 (2 pcs.)Vinyl sheathArmorAnticorrosiveshea

2-16 PowerTo Hull Unit(cable 10S2078)To Processor Unit(cable 10S1258-1)TB-B101CN-B101CN-B102Satellite CompassTB-B10CableNo.12345678910111213141516Cla

2-172.6 Control Box of Hull Unit Connect the power cable TYPCY-4 (3φ) and the transceiver unit cable (10S2078, end with shorter peeled portion) as s

2-18 FUSE FUSEF601 F602INPUT(TB-B101)FUSEF601 F602100V110V 20A 20A115V220V230V10A

2-192.8 Controller Extension Kit (Junction Box) Wire the junction box of the controller extension kit as shown below. Cable from TB-1 in control bo

2-20 This page intentionally left blank.

3-13. ADJUSTMENT AND CHECK 3.1 Hull Unit Check Setting transmission on Default setting of transmission is OFF. Set the transmission on as follows:

iiiTABLE OF CONTENTS SYSTEM CONFIGURATION...iv EQUIPMENT LISTS

3-2 4. Choose YES and press the [MENU] key. OTHERS MENU QUITQUITQUITMARK DISPLAY...MARK SIZE...DATA DISPLAY...CURRENT VEC & WIND...NET SONDE S

3-33. Remove the cover of the raise/lower control box and use a multimeter to measure the following voltages: Terminal Terminal No. Voltage TB-C101

3-4 3.2 Heading Adjustment When the BOW mark on the flange of the hull unit cannot be directed toward ship’s bow, adjust the heading so an echo which

3-5 MENU QUITQUITOTHERSQUITCANCELLANGUAGE : EnglishHEADING ADJUST1 : 0°HEADING ADJUST2 : 0°PROPELLER DIREC : -180°ES2 SELECT : ESES DRAFT OF

3-6 3.3 Configuring Own Ship Mark Set own ship’s dimensions and the location of the transducer to accurately display the own ship mark on the displa

3-7Ship'sLengthShip's WidthTD Position 1TD Position 2(Negative valuefor port)5. Choose ▲ or ▼ and then operate the [MENU] key to set the sh

3-8 CIF BAUD RATE: Set the transmission rate for the CIF port. If the CS-120A is connected, choose “2400 bps”. (2400 bps, 4800 bps, 9600 bps, 19200 b

3-9SPEED & COURSE: Choose the input format for ship’s speed and course data. When choosing the LOG&HEADING, the heading data is used instead

3-10 Data sentences NMEA Input sentences Sentence Main data source Main data GNS GPS Latitude, longitude GGA GPS Latitude, longitude RMA Loran C

3-113.4.3 OTHERS menu MENU QUITQUITOTHERSLANGUAGE : EnglishHEADING ADJUST1 : 0HEADING ADJUST2 : 0PROPELLER DIREC : -180ES2 SELECT : ESES DR

iv SYSTEM CONFIGURATION System with locally supplied monitor Note 1: Power Kit (option, installed inprocessor unit) required to connect CS-120A.220 V

3-12 TRACKBALL SPEED: Choose the speed of trackball movement (inside menu window only). (SLOW, NORMAL, FAST) HULL UNIT STROKE: Choose the stroke len

3-133.6 DIP Switch Setting IFESSCANSCAN2DUALDCONJ1IFES board (10P6903)DCON board (10P6987)J496, J497J1J496J497DCAC Processor unit, inside view 3.6.

3-14 3.6.2 Choosing echosounder signal There are two kinds of echosounder signals, AC signal and DC signal. Set the appropriate jumper on the CONE b

4-14. CONNECTING EXTERNAL INTERFACE CS-120A The External Interface CS-120A functions to enable upgrading from a past CSH series sonar. However, we r

4-2 3. Fix the power supply pcb (supplied) to the power module with four spacers (supplied). 4. Connect two VH connectors (provided on the power mo

%1&'016;2'%2⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105+056#..

CODE NO.CODE NO.CODE NO.CODE NO.007-008-780TYPETYPETYPETYPEFP10-02901略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-0 ACCESSO

㧼㧭㧯㧷㧵㧺㧳ޓ㧸㧵㧿㨀%7: (58,,'0#/'176.+0'&'5%4+26+10%1&'ͳ36;࡙࠾࠶࠻ 70+6ᠲ૞ㇱ%10641.70+

㧼㧭㧯㧷㧵㧺㧳ޓ㧸㧵㧿㨀%7: (58#$0#/'176.+0'&'5%4+26+10%1&'ͳ36;࡙࠾࠶࠻ 70+6ㅍฃାⵝ⟎64#05%'+8'470+6

%1&'016;2'52+6'/010#/'1(2#46176.+0'&9)01142'45'62'48'552#4'91

vSystem with FURUNO monitor PROCESSOR UNITFSV-8402Current IndicatorE/S InterfaceVI-1100ANet SondeJunction BoxCS-170E/S InterfaceVI-1100AExternalInter

%1&'016;2'%2⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105+056#..

㧼㧭㧯㧷㧵㧺㧳ޓ㧸㧵㧿㨀%7: (586(5860#/'176.+0'&'5%4+26+10%1&'ͳ36;࡙࠾࠶࠻ 70+6਄ਅⵝ⟎*7..70+6(58

%1&'016;2'52+6'/010#/'1(2#46176.+0'&9)01142'45'62'48'552#4'91

%1&'016;2'(58.6⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105%7

%1&'016;2'%2⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105+056#..

%1&'016;2'⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105#%%'5514+'5ઃዻຠ⴫ޓޓޓޓޓ

A-23

D-1

D-2

D-3

vi EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Control Unit FSV-8401-10 —1 w/10 m cable FSV-8402-100 — 110 VAC Processor Unit F

D-4

D-5

D-6

D-7

D-8

D-9

Nov.22'06T.MatsuguchiD-10

Nov.22'06T.MatsuguchiD-11

D-12

D-16D-13

1-11. MOUNTING THE EQUIPMENT 1.1 Hull Unit Note 1: The raise/lower control box on the hull unit contains a motion sensor. Therefore, never drop the

D-14

Mar.14'07 R.EsumiD-15

DCBA654321FURUNO ELECTRIC CO., LTD.INTERCONNECTION DIAGRAMCOLOR SCANNING SONAR相互結線図カラースキャニングソナーFSV-84名称NAMETITLEDWG No.MASSSCALEAPPROVEDCHECKEDDRAWNkg

DCBA654321FURUNO ELECTRIC CO., LTD.INTERCONNECTION DIAGRAM相互結線図名称NAMETITLEDWG No.MASSSCALEAPPROVEDCHECKEDDRAWNkgT.YAMASAKI＊１）造船所手配。注記＊２）オプション。＊３）コネクタは

FURUNO ELECTRIC CO., LTD.NOTE*1: SHIPYARD SUPPLY.注記＊１）造船所手配。＊２）オプション。＊３）コネクタは工場にて取付済み。＊４）00-8016-038-313761HVF*3: CONNECTOR PLUGS FITTED AT FACTORY.*4

CB123DADWG.No.SCALECHECKEDAPPROVEDDRAWNMASSkg名称NAMETITLEINTERCONNECTION DIAGRAM制御部外部信号接続相互結線図PROCESSOR UNIT EXTERNAL INTERFACEJ10GNDSONDE_WLGNDGNDSOND