Furuno 1734C User Manual

MODEL 1724C MARINE RADARMODEL 1734C MARINE RADARGD-1720C COLOR VIDEO PLOTTER VX2www.furuno.co.jpBack

viiiThis page is intentionally left blank.

11. MOUNTING NOTICEDo not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment.Those items contain org

2 1.1.1 Mounting procedure Tabletop, overhead mounting Follow the procedure below to mount the display unit on a tabletop or the overhead. 1. Fix t

3Flush mounting Note: Use supplied pan head screws when the thickness of the bulkhead is from 11 to 14 mm. For bulkhead which exceeds 14 mm in thic

4 1.2 Mounting of Antenna Units 1.2.1 Mounting considerations When selecting a mounting location for the antenna unit keep in mind the following poin

51.2.2 Mounting antenna unit of MODEL 1724C 1. Remove mounting hardware at the bottom of the antenna unit; four each of hex bolts (M10X20), sprin

6 4. Unfasten four screws to remove the cover. Discard the packing material in the radome. Remove and discard the packing material.Snap holder Anten

75. Unfasten the cable of the rotation detector from the cable clamps. 6. Unfasten 11 screws to dismount the shield plate. Discard screw marked w

8 Rubber gasketGasketCable GlandSectional viewMounting baseRubber gasket Antenna unit, inside view 8. Referring to the figure shown below, fasten

99. Attach EMI core (supplied) to antenna cable between cable ties. Set the fixing band to the EMI core. This bend should be facing cable entry.

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANTelephone :

10 1.2.3 Mounting antenna unit of MODEL 1734C 1. Open the antenna unit packing box carefully. 2. Unbolt the four bolts at the base of the radome t

11FlatwasherSpringwasherPlatformAntenna base plateM10 x 25Hex boltRadome5 - 10 mmApply silicone sealant.Effectivethread length25 mmGasket How to f

12 to one of the screws of the cable clamping plate9-pin connector:to J801 on MD-92084-pin connector:to J802 on MD-920813-pin connector:to J611 on IF

1310. Attach the EMC core supplied as shown below. J806J805J803J804J802J801MotorJ613J611J1EMC coreE04SS251512(Above cableclampingplate)Cableentranc

14 1.2.4 Mounting the optional mounting bracket A mounting bracket for fastening the antenna unit to a mast on a sailboat is optionally available.

15Support plate(A) Assembling the mounting bracket(B) Fastening antenna to mounting bracket How to assemble and mount the optional mounting br

16 2. WIRING 2.1 Standard Wiring All wirings are terminated at the rear of the display unit. CAUTIONThe power cable is shipped with a 10A fuse(5A on

17Signal cable connection 1. Remove the waterproofing cover from the DJ-1 at the back of the display unit. 2. Connect the signal cable to DJ-1 on

18 DATA1 to DATA3 ports Other equipments can be connected here as shown below. DATA1 (7P) DATA2 (6P) DATA3 (7P) GPS receiver GP-310B/320B, NMEA eq

192.2 External Buzzer (OP03-136, option) Connection The optional external buzzer provides a louder alert when the guard alarm is violated. Extern

iWARNINGRadio FrequencyRadiation HazardThe radar antenna emits electromagneticradio frequency (RF) energy which can beharmful, particularly to your

20 2.3 How to Connect with a PC When connecting with the personal computer, prepare the optional cable assy MJ-A7SPF0007-050C and D-sub 9 pins plug

213. SETTING UP THE EQUIPMENT 3.1 Setting up with the Installation Wizard After you have installed the equipment, set up the equipment with the i

22 CAUTION: Ensure that the settings to be loaded are compatible with this NavNet unit. Improper settings will damage the equipment. 7. The screen f

2311. Choose DEVICE NUMBER, RADAR SOURCE or SOUNDER SOURCE as appropriate and then press the EDIT soft key. One of the following displays appears d

24 13. After choosing ALL sources, press the NEXT soft key, and the RADAR SETUP menu appears. If you do not have a radar installed, press the NEXT so

2520. Choose TUNING and then press the EDIT soft key. TUNING▲{ ON~ OFF▼ 21. Choose ON and then press the ENTER soft key. Then, the radar’s video an

26 23. Choose HEADING ADJUST and then press the EDIT soft key. HEADING ADJUST{ ON~ OFF 24. Choose ON and then press the ENTER soft key. You have mo

27NAV SETUP menu description Item Description Settings (Default in bold) Position Source Chooses source of position data. FURUNO BB GPS: GPS Rec

28 28. After setting up navigation equipment, press the NEXT soft key, and the GPS SETUP menu appears. This menu sets ups the FURUNO GPS receiver GP-

29GPS SETUP menu description (con’t from previous page) Item Description Settings Default Setting Spd/Cse Smoothing During position fixing, ship’s

iiTABLE OF CONTENTS EQUIPMENT LISTS ...iii SYSTEM

30 GPS SETUP menu description (con’t from previous page) Item Description Settings Default Setting Fix Mode Choose position fixing method: 2D (three

3132. Choose item and press the EDIT soft key. Choose appropriate setting and then press the ENTER soft key. Refer to the table and sentence descri

32 $GPGLL,3415.2345,N,13520.5301,E,152500.00,A*E7<CR><LF>$GPGLL,3415.2345,N,13520.5301,E,152500.00,A*E7<CR><LF>$GPGLL,3415.

333.2 Checking Magnetron Heater Voltage Magnetron heater voltage is formed on the PTU or MD Board of the antenna unit, and preadjusted at the fact

34 3.3 Remote Controller Setting A remote controller can be set exclusively for use with a specific display unit, in the case of multiple NavNet dis

NAME OUTLINE Q'TYDESCRIPTION/CODE №ＰＡＣＫＩＮＧ ＬＩＳＴ19AW-X-9851 -4 RDP-148-E-*-CS1/1NAME OUTLINE Q'TYDESCRIPTION/CODE №ユニット UNIT指示部DISPLAY UNIT1*

㧼㧭㧯㧷㧵㧺㧳ޓ㧸㧵㧿㨀#-: 45$0#/'176.+0'&'5%4+26+10%1&'ͳ36;࡙࠾࠶࠻ 70+6㧔ቢ㧕ⓨਛ✢ㇱ#06'00#70+645$

%1&'016;2'⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105+056#..#6+10/#6'4+#.5Ꮏ੐᧚ᢱ

%1&'016;2'52+6'/010#/'1(2#46176.+0'&9)01146;2'012'45'62'48'

Y. HataiD-1

iiiEQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Display unit RDP-148 - 1 RSB-110-070-A - 1 For MODEL1724C Antenna unit RSB

Y. HataiD-2

Y. HataiD-3

Y. HataiD-4

NAMETYPE名称kgDRAWNCHECKEDAPPROVEDDWG.No.SCALE MASS3421CBADJ1*2キダイクロシロアカミドリｼﾛ/ﾐﾄﾞﾘ(太)モモﾄﾞｳｼﾞｸTUNING_CONTTUNING_INDVIDEOGNDSHIELDA/C SEAGAINP/L_AMOTOR(+)

NAMETYPE名称kgDRAWNCHECKEDAPPROVEDDWG.No.SCALE MASS3421CBADJ1*221(+)(-)12整流器RECTIFIERPR-6256クロ BLKシロ WHT(+)(-)3DPYC-1.5 *1*25432167*2GND+12VSHIELDJ13511

名称NAMEDABC231kg相互結線図INTERCONNECTION DIAGRAMビデオプロッタVIDEO PLOTTER21(+)(-)整流器RECTIFIERクロ BLKシロ WHT(+)(-)3DPYC-1.5 *1GNDJ135156 12PR-6224VDC5432167+12VSHI

iv Optional supply Name Type Code No. Qty Remarks 000-013-484 For 100 VAC 000-013-485 For 110 VAC 000-013-486 For 220 VAC Rectifier PR-62 000-013-

vSYSTEM CONFIGURATIONS All NavNet products incorporate a “network circuit board” to integrate each NavNet product on board through an optional LAN

viNetwork SounderETR-6/10NETR-30NGPS receiverGP-310B/320B12 - 24 VDC100/110/115/220/230 VAC1φ, 50/60 HzRemoteControllerRMC-100External buzzerEcho sou

viiAntenna UnitGP-310B/320BHUBRadar dataPlotter dataNetwork SounderETR-6/10NETR-30N(option)Sounder dataNote: The picture disappears10 seconds after